Is it a bad idea to drill a hole through this door frame to pass wires?
1
I want to pass my ethernet, speaker and sub wires into my newly built media/bar cabinet, but I hate having to pass them under the door, so I'd like to drill a hole as shown by the green circle in the image.
Bad idea?
doors closet
edited 1 hour ago
Tim Medora
1034
asked 11 hours ago
jwilcox09
1062
New contributor
jwilcox09 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
1
I want to pass my ethernet, speaker and sub wires into my newly built media/bar cabinet, but I hate having to pass them under the door, so I'd like to drill a hole as shown by the green circle in the image.
Bad idea?
doors closet
edited 1 hour ago
Tim Medora
1034
asked 11 hours ago
jwilcox09
1062
New contributor
jwilcox09 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
10 hours ago
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
7 hours ago
1
You're not going to run mains power through this, are you?
– Harper
7 hours ago
add a comment |
1
1
1
I want to pass my ethernet, speaker and sub wires into my newly built media/bar cabinet, but I hate having to pass them under the door, so I'd like to drill a hole as shown by the green circle in the image.
Bad idea?
doors closet
edited 1 hour ago
Tim Medora
1034
asked 11 hours ago
jwilcox09
1062
New contributor
jwilcox09 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I want to pass my ethernet, speaker and sub wires into my newly built media/bar cabinet, but I hate having to pass them under the door, so I'd like to drill a hole as shown by the green circle in the image.
Bad idea?
doors closet
doors closet
edited 1 hour ago
Tim Medora
1034
asked 11 hours ago
jwilcox09
1062
New contributor
jwilcox09 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 1 hour ago
Tim Medora
1034
asked 11 hours ago
jwilcox09
1062
New contributor
jwilcox09 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 1 hour ago
Tim Medora
1034
edited 1 hour ago
Tim Medora
1034
edited 1 hour ago
Tim Medora
1034
1034
asked 11 hours ago
jwilcox09
1062
New contributor
jwilcox09 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 11 hours ago
jwilcox09
1062
asked 11 hours ago
jwilcox09
1062
1062
New contributor
jwilcox09 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
jwilcox09 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
jwilcox09 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
10 hours ago
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
7 hours ago
1
You're not going to run mains power through this, are you?
– Harper
7 hours ago
add a comment |
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
10 hours ago
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
7 hours ago
1
You're not going to run mains power through this, are you?
– Harper
7 hours ago
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
10 hours ago
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
10 hours ago
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
7 hours ago
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
7 hours ago
1
1
You're not going to run mains power through this, are you?
– Harper
7 hours ago
You're not going to run mains power through this, are you?
– Harper
7 hours ago
add a comment |
2 Answers
2
active
oldest
votes
3
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered 10 hours ago
BillWeckel
95018
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
8 hours ago
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
5 hours ago
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
5 hours ago
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
5 hours ago
add a comment |
2
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered 10 hours ago
Rohit Saxena
1212
New contributor
Rohit Saxena is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
10 hours ago
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
10 hours ago
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
10 hours ago
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
8 hours ago
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
4 hours ago
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
jwilcox09 is a new contributor. Be nice, and check out our Code of Conduct.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f153654%2fis-it-a-bad-idea-to-drill-a-hole-through-this-door-frame-to-pass-wires%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
3
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered 10 hours ago
BillWeckel
95018
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
8 hours ago
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
5 hours ago
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
5 hours ago
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
5 hours ago
add a comment |
3
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered 10 hours ago
BillWeckel
95018
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
8 hours ago
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
5 hours ago
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
5 hours ago
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
5 hours ago
add a comment |
3
3
3
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered 10 hours ago
BillWeckel
95018
Not a bad idea what so ever. However, let me clarify on the posted answer... A hole saw can be used to cut clean perfect holes, but are limited in cut depth. You'll most likely need to use the hole saw on both sides of the jamb.
A hole hog, as another commenter mentioned, is also known as an auger bit. It has a pointed threaded tip that will pull the bit thru whatever material you're trying to drill thru until the tip can't pull anymore. From there you'll need a little extra force to get the bit to finish it's cut.
Both are feasible tools for what you're looking to do.
answered 10 hours ago
BillWeckel
95018
answered 10 hours ago
BillWeckel
95018
answered 10 hours ago
BillWeckel
95018
answered 10 hours ago
BillWeckel
95018
95018
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
8 hours ago
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
5 hours ago
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
5 hours ago
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
5 hours ago
add a comment |
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
8 hours ago
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
5 hours ago
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
5 hours ago
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
5 hours ago
4
4
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
8 hours ago
Micro-note... the auger bit is likely to produce a bunch of tearout on the far side. Drill until the threaded point just emerges, then drill the remainder from that side.
– Aloysius Defenestrate
8 hours ago
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
5 hours ago
A 3/8" bit extender will put a holesaw through anything; it's just a pita.
– Mazura
5 hours ago
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
5 hours ago
If you get a long enough bit extender (like 18") you can put the hole inline with the track and go straight thru (butchering a hole from both sides, using whatever bits - 'butchered' because it will be at a slight angle and so needs be a little larger).
– Mazura
5 hours ago
1
1
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
5 hours ago
A bit extender won't change the depth of the hole saw bit. If the hole saw bit depth is 2", then you can only cut 2" deep before you have to remove the plug from the bit to cut further...
– BillWeckel
5 hours ago
add a comment |
2
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered 10 hours ago
Rohit Saxena
1212
New contributor
Rohit Saxena is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
10 hours ago
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
10 hours ago
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
10 hours ago
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
8 hours ago
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
4 hours ago
add a comment |
2
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered 10 hours ago
Rohit Saxena
1212
New contributor
Rohit Saxena is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
10 hours ago
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
10 hours ago
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
10 hours ago
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
8 hours ago
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
4 hours ago
add a comment |
2
2
2
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered 10 hours ago
Rohit Saxena
1212
New contributor
Rohit Saxena is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I would suggest getting a hole cutter instead of drilling a hole so the hole can be future proofed if you want to pass more wires someday.
answered 10 hours ago
Rohit Saxena
1212
New contributor
Rohit Saxena is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
answered 10 hours ago
Rohit Saxena
1212
New contributor
Rohit Saxena is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
answered 10 hours ago
Rohit Saxena
1212
answered 10 hours ago
Rohit Saxena
1212
1212
New contributor
Rohit Saxena is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Rohit Saxena is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Rohit Saxena is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
10 hours ago
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
10 hours ago
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
10 hours ago
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
8 hours ago
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
4 hours ago
add a comment |
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
10 hours ago
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
10 hours ago
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
10 hours ago
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
8 hours ago
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
4 hours ago
1
1
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
10 hours ago
Those both sound like drilling a hole to pass wires. Whats the difference between them?
– HazardousGlitch
10 hours ago
1
1
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
10 hours ago
A hole cutter can make a bigger hole then a big gauged drill. In the past I have found it hard to turn a small hole into a bigger hole with a hole cutter because they're is nothing in the center for the drill bit to drill into.
– Rohit Saxena
10 hours ago
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
10 hours ago
Never heard of it referred to as a hole cutter before. I'm used to hole saw for creating a very clean hole with a plug as a result and hole hog which cuts through very quickly, shredding everything in it's path, both which come in larger diameters than normal drill bits.
– HazardousGlitch
10 hours ago
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
8 hours ago
Hole saw would be brutal to get through there, use an auger as @BillWickel suggests
– Gary Bak
8 hours ago
1
1
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
4 hours ago
"hole saw" would be the normal name for a sawblade bent into a cylinder. "hole cutter" would be a something similar to a lathe cutter tool on a radial post something like a really big caliper that can be adjusted. OP probably doesn't have room for anything wide, and the drill's body will probably be the limiting factor, getting it pressed up against the adjacent wall while keeping the holesaw straight.
– Criggie
4 hours ago
add a comment |
jwilcox09 is a new contributor. Be nice, and check out our Code of Conduct.
draft saved
draft discarded
jwilcox09 is a new contributor. Be nice, and check out our Code of Conduct.
jwilcox09 is a new contributor. Be nice, and check out our Code of Conduct.
jwilcox09 is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
draft saved
draft discarded
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f153654%2fis-it-a-bad-idea-to-drill-a-hole-through-this-door-frame-to-pass-wires%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Yes, it's a good idea (see answer below). Based on your picture, it's a older house so there is likely a 4" stud that you'll need to drill through so be ready for that and be ready for nails.
– HazardousGlitch
10 hours ago
It doesn't deserve a new answer because the other ones are perfect in their own right. Just an addition: use a larger tool to make the hole, making sure that all current and future plugs can pass through, not just the wires. Then simply cover the hole with what is known as a cable (desk) grommet, something like this: ae01.alicdn.com/kf/UTB8zAwbXnvEXKJk43KUq6xdxpXa4.jpg
– Gábor
7 hours ago
1
You're not going to run mains power through this, are you?
– Harper
7 hours ago