Can I run PEX directly into my clothes washer?
up vote
1
down vote
favorite
Aside from the difficulty of finding the right fitting, is there a specific reason I need to connect my clothes washer to the taps via a hose instead of directly via PEX?
I ask because hoses are regarded as a poinit of with a high likely hood of failure. Given PEX and PEX fittings tolerance to bending, freezing, and their ease of rotation around a joint, it seems like PEXing directly into my washer would be preferred vs spending $100+ on fittings, valves and hoses to do it the traditional way.
My thought was to T off a supply line and use two elbows to ensure flexibility in all directions. After the 'T', I'd have 2.5 feet of PEX that I won't strap down to allow flex in the 'y' and 'z' directions, and then an elbow and another 2.5 feet before the shutoff valve to allow flex in the 'x' and 'z':
Fittings
If it is okay to connect directly, is it okay to use a plastic elbow? (the male connection on my clothes washer is plastic) such as the sea tech one pictured below, or should I use brass only?
plumbing washing-machine hose
add a comment |
up vote
1
down vote
favorite
Aside from the difficulty of finding the right fitting, is there a specific reason I need to connect my clothes washer to the taps via a hose instead of directly via PEX?
I ask because hoses are regarded as a poinit of with a high likely hood of failure. Given PEX and PEX fittings tolerance to bending, freezing, and their ease of rotation around a joint, it seems like PEXing directly into my washer would be preferred vs spending $100+ on fittings, valves and hoses to do it the traditional way.
My thought was to T off a supply line and use two elbows to ensure flexibility in all directions. After the 'T', I'd have 2.5 feet of PEX that I won't strap down to allow flex in the 'y' and 'z' directions, and then an elbow and another 2.5 feet before the shutoff valve to allow flex in the 'x' and 'z':
Fittings
If it is okay to connect directly, is it okay to use a plastic elbow? (the male connection on my clothes washer is plastic) such as the sea tech one pictured below, or should I use brass only?
plumbing washing-machine hose
1
TIP: Hoses are marked up like 1000% at the store. Usually they're free, or at most 5 dollars from a local used appliance store. They usually have hundreds of them laying around.
– freshop
yesterday
@freshop that will be very valuable info when I go to flush my on demand hot-water tank. Sadly the brass connections are the major expense (~$70 for the minimal ones in the big box stores by me).
– virtualxtc
yesterday
I know this isn't supposed to be for shopping, but if you're in the US like me try looking up Quarter Turn Ball Valve PEX Washing Machine Outlet Box should be around $30
– freshop
yesterday
@freshop Ya - I saw those but they are PEX A type (heat expanded fitting). The normal (crimp) PEX ones are $70.
– virtualxtc
yesterday
1
Washing machines move around a lot yiu need the flexibility that the hose provides.
– Kris
16 hours ago
add a comment |
up vote
1
down vote
favorite
up vote
1
down vote
favorite
Aside from the difficulty of finding the right fitting, is there a specific reason I need to connect my clothes washer to the taps via a hose instead of directly via PEX?
I ask because hoses are regarded as a poinit of with a high likely hood of failure. Given PEX and PEX fittings tolerance to bending, freezing, and their ease of rotation around a joint, it seems like PEXing directly into my washer would be preferred vs spending $100+ on fittings, valves and hoses to do it the traditional way.
My thought was to T off a supply line and use two elbows to ensure flexibility in all directions. After the 'T', I'd have 2.5 feet of PEX that I won't strap down to allow flex in the 'y' and 'z' directions, and then an elbow and another 2.5 feet before the shutoff valve to allow flex in the 'x' and 'z':
Fittings
If it is okay to connect directly, is it okay to use a plastic elbow? (the male connection on my clothes washer is plastic) such as the sea tech one pictured below, or should I use brass only?
plumbing washing-machine hose
Aside from the difficulty of finding the right fitting, is there a specific reason I need to connect my clothes washer to the taps via a hose instead of directly via PEX?
I ask because hoses are regarded as a poinit of with a high likely hood of failure. Given PEX and PEX fittings tolerance to bending, freezing, and their ease of rotation around a joint, it seems like PEXing directly into my washer would be preferred vs spending $100+ on fittings, valves and hoses to do it the traditional way.
My thought was to T off a supply line and use two elbows to ensure flexibility in all directions. After the 'T', I'd have 2.5 feet of PEX that I won't strap down to allow flex in the 'y' and 'z' directions, and then an elbow and another 2.5 feet before the shutoff valve to allow flex in the 'x' and 'z':
Fittings
If it is okay to connect directly, is it okay to use a plastic elbow? (the male connection on my clothes washer is plastic) such as the sea tech one pictured below, or should I use brass only?
plumbing washing-machine hose
plumbing washing-machine hose
edited yesterday
asked yesterday
virtualxtc
1,68261530
1,68261530
1
TIP: Hoses are marked up like 1000% at the store. Usually they're free, or at most 5 dollars from a local used appliance store. They usually have hundreds of them laying around.
– freshop
yesterday
@freshop that will be very valuable info when I go to flush my on demand hot-water tank. Sadly the brass connections are the major expense (~$70 for the minimal ones in the big box stores by me).
– virtualxtc
yesterday
I know this isn't supposed to be for shopping, but if you're in the US like me try looking up Quarter Turn Ball Valve PEX Washing Machine Outlet Box should be around $30
– freshop
yesterday
@freshop Ya - I saw those but they are PEX A type (heat expanded fitting). The normal (crimp) PEX ones are $70.
– virtualxtc
yesterday
1
Washing machines move around a lot yiu need the flexibility that the hose provides.
– Kris
16 hours ago
add a comment |
1
TIP: Hoses are marked up like 1000% at the store. Usually they're free, or at most 5 dollars from a local used appliance store. They usually have hundreds of them laying around.
– freshop
yesterday
@freshop that will be very valuable info when I go to flush my on demand hot-water tank. Sadly the brass connections are the major expense (~$70 for the minimal ones in the big box stores by me).
– virtualxtc
yesterday
I know this isn't supposed to be for shopping, but if you're in the US like me try looking up Quarter Turn Ball Valve PEX Washing Machine Outlet Box should be around $30
– freshop
yesterday
@freshop Ya - I saw those but they are PEX A type (heat expanded fitting). The normal (crimp) PEX ones are $70.
– virtualxtc
yesterday
1
Washing machines move around a lot yiu need the flexibility that the hose provides.
– Kris
16 hours ago
1
1
TIP: Hoses are marked up like 1000% at the store. Usually they're free, or at most 5 dollars from a local used appliance store. They usually have hundreds of them laying around.
– freshop
yesterday
TIP: Hoses are marked up like 1000% at the store. Usually they're free, or at most 5 dollars from a local used appliance store. They usually have hundreds of them laying around.
– freshop
yesterday
@freshop that will be very valuable info when I go to flush my on demand hot-water tank. Sadly the brass connections are the major expense (~$70 for the minimal ones in the big box stores by me).
– virtualxtc
yesterday
@freshop that will be very valuable info when I go to flush my on demand hot-water tank. Sadly the brass connections are the major expense (~$70 for the minimal ones in the big box stores by me).
– virtualxtc
yesterday
I know this isn't supposed to be for shopping, but if you're in the US like me try looking up Quarter Turn Ball Valve PEX Washing Machine Outlet Box should be around $30
– freshop
yesterday
I know this isn't supposed to be for shopping, but if you're in the US like me try looking up Quarter Turn Ball Valve PEX Washing Machine Outlet Box should be around $30
– freshop
yesterday
@freshop Ya - I saw those but they are PEX A type (heat expanded fitting). The normal (crimp) PEX ones are $70.
– virtualxtc
yesterday
@freshop Ya - I saw those but they are PEX A type (heat expanded fitting). The normal (crimp) PEX ones are $70.
– virtualxtc
yesterday
1
1
Washing machines move around a lot yiu need the flexibility that the hose provides.
– Kris
16 hours ago
Washing machines move around a lot yiu need the flexibility that the hose provides.
– Kris
16 hours ago
add a comment |
3 Answers
3
active
oldest
votes
up vote
3
down vote
Aside from the fact that I don’t think it would be allowed by code it would be inconvenient and if there was ever a problem with the mechanics inside your machine and water started spewing out all over your floor you wouldn’t have a way to shut it off or disconnected easily.
Trying to save money now may cost you more money in the long run.
Buy stainless steel braided hoses and if you’re still worried get an auto shut off water detection system.
Do it right once or do it wrong once and then do it right the second time.
I have the valves already for the washer / laundry sink, but my experience has been that it's very difficult to convince a partner who isn't mechanically inclined to remember to shut these off, especially since the dryer also needs water for it's steam functions. Auto shut off valve is already purchased as I don't trust the internal parts of the machine to last.
– virtualxtc
yesterday
1
Not much we can do about an incompetent or more than likely and indifferent partner. It does not take much mechanical aptitude to turn a valve. People generally don’t turn their washing machine valves off after every use.
– Alaska man
yesterday
My last partner was so bad I installed one of those timber based shutoffs. Of course the timer mechanism failed after 1.5 yrs, so I'm trying to get away from such solutions.
– virtualxtc
yesterday
2
First person I have ever heard of turning the water off after each cycle. Sure if gone in the winter it would make sense, but using the wrong fittings maybe it should be turned off to hide the hack job when it fails.
– Ed Beal
yesterday
Where is such a setup not allowed by code?
– virtualxtc
3 hours ago
add a comment |
up vote
1
down vote
I think it's a good idea, though I've never seen a washer hose fail ("high likelihood" is probably still point-zero-zero-something percent per year). Some caveats:
- Pex, while fairly flexible, probably isn't going to take repeated long-term movement like rubber or vinyl. Leave enough of a loop between the wall and the machine so that no part of the tube is regularly stressed by the natural vibration of the machine (and you moving it to clean out dust bunnies).
- You might find that you wish you had shutoff valves close at hand. In fact, it may be required by code.
- Pex, being stiff, may want to jump around a bit when the machine opens and closes its internal valves. This could cause some slapping behind the machine. You might need to secure the lines to prevent them doing so.
I've been in a house when a rubber washer hose failed, but you might be right about the braided metal ones (it's just super expensive). Anyway, I updated my question to better explain how I was planning to get the flex needed.
– virtualxtc
yesterday
add a comment |
up vote
0
down vote
All though I am not sure if this is a code enforcement issue, the one issue I see is the flexibility of the hoses to allow the machine to "wobble" or "jump" when out of balance. Therefore not breaking the pipe or elbow, or slipping off the pipe at the connection point.
Updated my question to explain how I was planning to work around this.
– virtualxtc
yesterday
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f152583%2fcan-i-run-pex-directly-into-my-clothes-washer%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
3 Answers
3
active
oldest
votes
3 Answers
3
active
oldest
votes
active
oldest
votes
active
oldest
votes
up vote
3
down vote
Aside from the fact that I don’t think it would be allowed by code it would be inconvenient and if there was ever a problem with the mechanics inside your machine and water started spewing out all over your floor you wouldn’t have a way to shut it off or disconnected easily.
Trying to save money now may cost you more money in the long run.
Buy stainless steel braided hoses and if you’re still worried get an auto shut off water detection system.
Do it right once or do it wrong once and then do it right the second time.
I have the valves already for the washer / laundry sink, but my experience has been that it's very difficult to convince a partner who isn't mechanically inclined to remember to shut these off, especially since the dryer also needs water for it's steam functions. Auto shut off valve is already purchased as I don't trust the internal parts of the machine to last.
– virtualxtc
yesterday
1
Not much we can do about an incompetent or more than likely and indifferent partner. It does not take much mechanical aptitude to turn a valve. People generally don’t turn their washing machine valves off after every use.
– Alaska man
yesterday
My last partner was so bad I installed one of those timber based shutoffs. Of course the timer mechanism failed after 1.5 yrs, so I'm trying to get away from such solutions.
– virtualxtc
yesterday
2
First person I have ever heard of turning the water off after each cycle. Sure if gone in the winter it would make sense, but using the wrong fittings maybe it should be turned off to hide the hack job when it fails.
– Ed Beal
yesterday
Where is such a setup not allowed by code?
– virtualxtc
3 hours ago
add a comment |
up vote
3
down vote
Aside from the fact that I don’t think it would be allowed by code it would be inconvenient and if there was ever a problem with the mechanics inside your machine and water started spewing out all over your floor you wouldn’t have a way to shut it off or disconnected easily.
Trying to save money now may cost you more money in the long run.
Buy stainless steel braided hoses and if you’re still worried get an auto shut off water detection system.
Do it right once or do it wrong once and then do it right the second time.
I have the valves already for the washer / laundry sink, but my experience has been that it's very difficult to convince a partner who isn't mechanically inclined to remember to shut these off, especially since the dryer also needs water for it's steam functions. Auto shut off valve is already purchased as I don't trust the internal parts of the machine to last.
– virtualxtc
yesterday
1
Not much we can do about an incompetent or more than likely and indifferent partner. It does not take much mechanical aptitude to turn a valve. People generally don’t turn their washing machine valves off after every use.
– Alaska man
yesterday
My last partner was so bad I installed one of those timber based shutoffs. Of course the timer mechanism failed after 1.5 yrs, so I'm trying to get away from such solutions.
– virtualxtc
yesterday
2
First person I have ever heard of turning the water off after each cycle. Sure if gone in the winter it would make sense, but using the wrong fittings maybe it should be turned off to hide the hack job when it fails.
– Ed Beal
yesterday
Where is such a setup not allowed by code?
– virtualxtc
3 hours ago
add a comment |
up vote
3
down vote
up vote
3
down vote
Aside from the fact that I don’t think it would be allowed by code it would be inconvenient and if there was ever a problem with the mechanics inside your machine and water started spewing out all over your floor you wouldn’t have a way to shut it off or disconnected easily.
Trying to save money now may cost you more money in the long run.
Buy stainless steel braided hoses and if you’re still worried get an auto shut off water detection system.
Do it right once or do it wrong once and then do it right the second time.
Aside from the fact that I don’t think it would be allowed by code it would be inconvenient and if there was ever a problem with the mechanics inside your machine and water started spewing out all over your floor you wouldn’t have a way to shut it off or disconnected easily.
Trying to save money now may cost you more money in the long run.
Buy stainless steel braided hoses and if you’re still worried get an auto shut off water detection system.
Do it right once or do it wrong once and then do it right the second time.
answered yesterday
Alaska man
2,597310
2,597310
I have the valves already for the washer / laundry sink, but my experience has been that it's very difficult to convince a partner who isn't mechanically inclined to remember to shut these off, especially since the dryer also needs water for it's steam functions. Auto shut off valve is already purchased as I don't trust the internal parts of the machine to last.
– virtualxtc
yesterday
1
Not much we can do about an incompetent or more than likely and indifferent partner. It does not take much mechanical aptitude to turn a valve. People generally don’t turn their washing machine valves off after every use.
– Alaska man
yesterday
My last partner was so bad I installed one of those timber based shutoffs. Of course the timer mechanism failed after 1.5 yrs, so I'm trying to get away from such solutions.
– virtualxtc
yesterday
2
First person I have ever heard of turning the water off after each cycle. Sure if gone in the winter it would make sense, but using the wrong fittings maybe it should be turned off to hide the hack job when it fails.
– Ed Beal
yesterday
Where is such a setup not allowed by code?
– virtualxtc
3 hours ago
add a comment |
I have the valves already for the washer / laundry sink, but my experience has been that it's very difficult to convince a partner who isn't mechanically inclined to remember to shut these off, especially since the dryer also needs water for it's steam functions. Auto shut off valve is already purchased as I don't trust the internal parts of the machine to last.
– virtualxtc
yesterday
1
Not much we can do about an incompetent or more than likely and indifferent partner. It does not take much mechanical aptitude to turn a valve. People generally don’t turn their washing machine valves off after every use.
– Alaska man
yesterday
My last partner was so bad I installed one of those timber based shutoffs. Of course the timer mechanism failed after 1.5 yrs, so I'm trying to get away from such solutions.
– virtualxtc
yesterday
2
First person I have ever heard of turning the water off after each cycle. Sure if gone in the winter it would make sense, but using the wrong fittings maybe it should be turned off to hide the hack job when it fails.
– Ed Beal
yesterday
Where is such a setup not allowed by code?
– virtualxtc
3 hours ago
I have the valves already for the washer / laundry sink, but my experience has been that it's very difficult to convince a partner who isn't mechanically inclined to remember to shut these off, especially since the dryer also needs water for it's steam functions. Auto shut off valve is already purchased as I don't trust the internal parts of the machine to last.
– virtualxtc
yesterday
I have the valves already for the washer / laundry sink, but my experience has been that it's very difficult to convince a partner who isn't mechanically inclined to remember to shut these off, especially since the dryer also needs water for it's steam functions. Auto shut off valve is already purchased as I don't trust the internal parts of the machine to last.
– virtualxtc
yesterday
1
1
Not much we can do about an incompetent or more than likely and indifferent partner. It does not take much mechanical aptitude to turn a valve. People generally don’t turn their washing machine valves off after every use.
– Alaska man
yesterday
Not much we can do about an incompetent or more than likely and indifferent partner. It does not take much mechanical aptitude to turn a valve. People generally don’t turn their washing machine valves off after every use.
– Alaska man
yesterday
My last partner was so bad I installed one of those timber based shutoffs. Of course the timer mechanism failed after 1.5 yrs, so I'm trying to get away from such solutions.
– virtualxtc
yesterday
My last partner was so bad I installed one of those timber based shutoffs. Of course the timer mechanism failed after 1.5 yrs, so I'm trying to get away from such solutions.
– virtualxtc
yesterday
2
2
First person I have ever heard of turning the water off after each cycle. Sure if gone in the winter it would make sense, but using the wrong fittings maybe it should be turned off to hide the hack job when it fails.
– Ed Beal
yesterday
First person I have ever heard of turning the water off after each cycle. Sure if gone in the winter it would make sense, but using the wrong fittings maybe it should be turned off to hide the hack job when it fails.
– Ed Beal
yesterday
Where is such a setup not allowed by code?
– virtualxtc
3 hours ago
Where is such a setup not allowed by code?
– virtualxtc
3 hours ago
add a comment |
up vote
1
down vote
I think it's a good idea, though I've never seen a washer hose fail ("high likelihood" is probably still point-zero-zero-something percent per year). Some caveats:
- Pex, while fairly flexible, probably isn't going to take repeated long-term movement like rubber or vinyl. Leave enough of a loop between the wall and the machine so that no part of the tube is regularly stressed by the natural vibration of the machine (and you moving it to clean out dust bunnies).
- You might find that you wish you had shutoff valves close at hand. In fact, it may be required by code.
- Pex, being stiff, may want to jump around a bit when the machine opens and closes its internal valves. This could cause some slapping behind the machine. You might need to secure the lines to prevent them doing so.
I've been in a house when a rubber washer hose failed, but you might be right about the braided metal ones (it's just super expensive). Anyway, I updated my question to better explain how I was planning to get the flex needed.
– virtualxtc
yesterday
add a comment |
up vote
1
down vote
I think it's a good idea, though I've never seen a washer hose fail ("high likelihood" is probably still point-zero-zero-something percent per year). Some caveats:
- Pex, while fairly flexible, probably isn't going to take repeated long-term movement like rubber or vinyl. Leave enough of a loop between the wall and the machine so that no part of the tube is regularly stressed by the natural vibration of the machine (and you moving it to clean out dust bunnies).
- You might find that you wish you had shutoff valves close at hand. In fact, it may be required by code.
- Pex, being stiff, may want to jump around a bit when the machine opens and closes its internal valves. This could cause some slapping behind the machine. You might need to secure the lines to prevent them doing so.
I've been in a house when a rubber washer hose failed, but you might be right about the braided metal ones (it's just super expensive). Anyway, I updated my question to better explain how I was planning to get the flex needed.
– virtualxtc
yesterday
add a comment |
up vote
1
down vote
up vote
1
down vote
I think it's a good idea, though I've never seen a washer hose fail ("high likelihood" is probably still point-zero-zero-something percent per year). Some caveats:
- Pex, while fairly flexible, probably isn't going to take repeated long-term movement like rubber or vinyl. Leave enough of a loop between the wall and the machine so that no part of the tube is regularly stressed by the natural vibration of the machine (and you moving it to clean out dust bunnies).
- You might find that you wish you had shutoff valves close at hand. In fact, it may be required by code.
- Pex, being stiff, may want to jump around a bit when the machine opens and closes its internal valves. This could cause some slapping behind the machine. You might need to secure the lines to prevent them doing so.
I think it's a good idea, though I've never seen a washer hose fail ("high likelihood" is probably still point-zero-zero-something percent per year). Some caveats:
- Pex, while fairly flexible, probably isn't going to take repeated long-term movement like rubber or vinyl. Leave enough of a loop between the wall and the machine so that no part of the tube is regularly stressed by the natural vibration of the machine (and you moving it to clean out dust bunnies).
- You might find that you wish you had shutoff valves close at hand. In fact, it may be required by code.
- Pex, being stiff, may want to jump around a bit when the machine opens and closes its internal valves. This could cause some slapping behind the machine. You might need to secure the lines to prevent them doing so.
answered yesterday
isherwood
44.3k453114
44.3k453114
I've been in a house when a rubber washer hose failed, but you might be right about the braided metal ones (it's just super expensive). Anyway, I updated my question to better explain how I was planning to get the flex needed.
– virtualxtc
yesterday
add a comment |
I've been in a house when a rubber washer hose failed, but you might be right about the braided metal ones (it's just super expensive). Anyway, I updated my question to better explain how I was planning to get the flex needed.
– virtualxtc
yesterday
I've been in a house when a rubber washer hose failed, but you might be right about the braided metal ones (it's just super expensive). Anyway, I updated my question to better explain how I was planning to get the flex needed.
– virtualxtc
yesterday
I've been in a house when a rubber washer hose failed, but you might be right about the braided metal ones (it's just super expensive). Anyway, I updated my question to better explain how I was planning to get the flex needed.
– virtualxtc
yesterday
add a comment |
up vote
0
down vote
All though I am not sure if this is a code enforcement issue, the one issue I see is the flexibility of the hoses to allow the machine to "wobble" or "jump" when out of balance. Therefore not breaking the pipe or elbow, or slipping off the pipe at the connection point.
Updated my question to explain how I was planning to work around this.
– virtualxtc
yesterday
add a comment |
up vote
0
down vote
All though I am not sure if this is a code enforcement issue, the one issue I see is the flexibility of the hoses to allow the machine to "wobble" or "jump" when out of balance. Therefore not breaking the pipe or elbow, or slipping off the pipe at the connection point.
Updated my question to explain how I was planning to work around this.
– virtualxtc
yesterday
add a comment |
up vote
0
down vote
up vote
0
down vote
All though I am not sure if this is a code enforcement issue, the one issue I see is the flexibility of the hoses to allow the machine to "wobble" or "jump" when out of balance. Therefore not breaking the pipe or elbow, or slipping off the pipe at the connection point.
All though I am not sure if this is a code enforcement issue, the one issue I see is the flexibility of the hoses to allow the machine to "wobble" or "jump" when out of balance. Therefore not breaking the pipe or elbow, or slipping off the pipe at the connection point.
answered yesterday
Jeff Cates
1,37017
1,37017
Updated my question to explain how I was planning to work around this.
– virtualxtc
yesterday
add a comment |
Updated my question to explain how I was planning to work around this.
– virtualxtc
yesterday
Updated my question to explain how I was planning to work around this.
– virtualxtc
yesterday
Updated my question to explain how I was planning to work around this.
– virtualxtc
yesterday
add a comment |
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f152583%2fcan-i-run-pex-directly-into-my-clothes-washer%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
1
TIP: Hoses are marked up like 1000% at the store. Usually they're free, or at most 5 dollars from a local used appliance store. They usually have hundreds of them laying around.
– freshop
yesterday
@freshop that will be very valuable info when I go to flush my on demand hot-water tank. Sadly the brass connections are the major expense (~$70 for the minimal ones in the big box stores by me).
– virtualxtc
yesterday
I know this isn't supposed to be for shopping, but if you're in the US like me try looking up Quarter Turn Ball Valve PEX Washing Machine Outlet Box should be around $30
– freshop
yesterday
@freshop Ya - I saw those but they are PEX A type (heat expanded fitting). The normal (crimp) PEX ones are $70.
– virtualxtc
yesterday
1
Washing machines move around a lot yiu need the flexibility that the hose provides.
– Kris
16 hours ago